Glosarium Teknis Transformer

A transformer with a single winding acting as both primary and secondary, providing voltage conversion through electromagnetic induction and direct electrical connection.

The total power in an AC circuit combining real (active) and reactive power, measured in kilovolt-amperes (kVA).

A heavy-duty transformer designed to supply power to electric arc furnaces used in steelmaking and metal smelting.

The American National Standards Institute standard series covering power transformer requirements for the North American market.

A distribution transformer using amorphous metal core material achieving 60-70% lower no-load losses than conventional silicon steel cores.

The reduction in transformer capacity and insulation performance required at high altitudes where air density is lower.

The ability of transformer insulation to withstand high-voltage surges from lightning or switching, measured in kV peak.

A gas-actuated protective relay between transformer tank and conservator detecting internal faults by sensing gas accumulation.

An insulated device allowing a conductor to pass through a grounded barrier while maintaining insulation integrity.

A metallic strip conducting electricity within switchgear, transformers, and distribution equipment.

A factory-assembled compact substation integrating transformer, HV/LV switchgear, and protection in a weatherproof enclosure.

China Compulsory Certification (3C mark) required for electrical equipment sold in the Chinese domestic market.

Conformite Europeenne marking required for electrical equipment in the European Economic Area.

Power dissipated in the transformer magnetic core due to hysteresis and eddy currents, also called iron loss or no-load loss.

Power lost as heat in transformer windings due to electrical resistance, proportional to the square of load current.

An instrument transformer producing secondary current proportional to primary current, for measurement and protection.

Standardized codes describing transformer cooling methods: O=Oil, N=Natural, A=Air, F=Forced, D=Directed flow.

A dry-type transformer with windings encapsulated in epoxy resin for fire safety and moisture resistance indoors.

A transformer stepping down voltage from the distribution network (11-33 kV) to utilization voltage (400/230V) for end consumers.

A transformer using air or solid insulation instead of liquid, ideal for indoor applications with fire safety priority.

A diagnostic technique analyzing gases dissolved in transformer oil to detect internal faults before they become critical.

The maximum electric field an insulating material can withstand before breakdown, measured in kV/mm.

Circulating currents induced in conductive materials by changing magnetic fields, causing energy losses in transformers.

International classification for transformer energy efficiency, IE1 (standard) to IE4 (premium) with progressively lower losses.

The voltage generated by electromagnetic induction in a transformer winding, proportional to flux change and turns.

Current drawn by transformer primary when energized with no load, consisting of magnetizing and core-loss components.

A transformer for EV charging stations handling harmonic-rich loads and variable power demands.

An electrostatic shield between transformer windings blocking capacitive coupling of high-frequency noise.

The number of AC cycles per second (50 or 60 Hz), determining transformer design parameters.

The extremely high current during a short circuit that transformers must withstand mechanically.

A diagnostic measuring furan compounds in transformer oil to assess cellulose insulation degradation.

A large power transformer stepping up generator voltage (11-25 kV) to transmission levels for grid connection.

A transformer providing a neutral point for grounding in ungrounded or delta-connected systems.

A transformer using SF6 or alternative gases as insulation instead of oil for fire safety and compact design.

Chinese national standards (Guobiao) for transformers including GB 1094, equivalent to IEC 60076 with local adaptations.

Integer multiples of fundamental frequency from non-linear loads, causing increased transformer losses and overheating.

The highest temperature within transformer winding insulation, determining aging rate and loading capability.

Energy lost in core steel from repeated reversal of magnetic domains each AC cycle, a component of core loss.

High-voltage and low-voltage insulated conduits for transformer winding connections through the grounded tank.

Total opposition to current flow in a transformer as a percentage, determining fault current and voltage regulation.

A high transient current when a transformer is first energized, caused by core saturation, reaching 10-30x rated.

Standardized temperature ratings for transformer insulation materials defining maximum operating temperatures.

The IEC standard series defining requirements for power transformers, the global reference standard.

The IEEE standard series for transformers, the primary reference for the North American market.

Complete power distribution solutions for industrial parks requiring reliable transformer infrastructure at multiple voltage levels.

IEEE standard specifying requirements for pad-mounted, self-protected distribution transformers for North American markets.

An enclosure providing accessible entry points for electrical cables, enabling circuit branching and connections within power systems.

Heat generated in electrical conductors proportional to current squared times resistance, the dominant source of transformer load loss.

A sealed enclosure on transformer tanks providing access to internal winding connections and tap changer linkages.

A transformer rating indicating ability to supply non-linear harmonic loads without exceeding temperature limits.

The apparent power rating of a transformer in kilovolt-amperes, determining load-carrying capacity.

The voltage at which a current transformer core begins to saturate, critical for protection CT performance.

An online oil purification system continuously filtering transformer oil through a side-loop circuit to remove moisture and particles.

A mechanism allowing transformer tap ratio changes while energized and under load for real-time voltage regulation.

Reactance from magnetic flux not linking both windings, a major component of transformer impedance.

A financial methodology assigning monetary value to transformer losses for optimal lifetime economic selection.

A high-voltage test simulating lightning surges to verify transformer insulation withstands transient overvoltages.

A protective device diverting high-voltage surges from lightning and switching to ground, safeguarding transformer insulation.

The laminated silicon steel assembly providing a low-reluctance path for magnetic flux, backbone of transformer operation.

The reactive component of no-load current establishing magnetic flux in the transformer core.

External enclosure housing transformer control wiring, terminals, and auxiliary circuits for substation connection.

The amount of water in transformer oil and solid insulation, critical for dielectric strength and insulation life.

The total magnetic field passing through the transformer core cross-section, fundamental to electromagnetic energy transfer.

Power consumed when energized but not supplying load, consisting of core losses (hysteresis + eddy currents).

The common connection point of a star (wye) winding where the three-phase voltage vector sum equals zero.

Enclosure protection ratings for electrical equipment specifying protection against environmental hazards.

Manufacturer's certified specifications on the transformer nameplate defining all critical parameters.

An automatic switching device on secondary network systems preventing reverse power flow from distributed generation sources.

A transformer using mineral oil as insulation and cooling medium, most common for outdoor power and distribution.

A device changing transformer tap positions under load without interrupting supply for automatic voltage regulation.

A condition where core flux exceeds design level due to excessive voltage or reduced frequency.

Equipment preventing moisture and oxygen from entering transformer oil, including conservators and sealed tanks.

The simplest transformer cooling method using natural oil circulation and natural air convection, requiring no pumps or fans.

A large transformer (>10 MVA) used in transmission networks for stepping voltage between system levels.

The ratio of real power (kW) to apparent power (kVA) indicating how effectively electrical power is utilized.

Localized electrical discharges in small insulation regions not bridging electrodes, indicating defects or aging.

A factory-assembled complete substation integrating transformer, switchgear, and protection for rapid installation.

A graphical representation of AC voltage and current relationships in a transformer showing magnitude and phase angle.

The instantaneous voltage relationship between primary and secondary terminals determining series/parallel connection compatibility.

Systematic processes ensuring transformer design, manufacturing, and testing meet all specified standards and customer requirements.

A separable connector enabling rapid, tool-free disconnection of transformer cables for maintenance and reconfiguration.

High-grade mineral or synthetic insulating fluid with optimized dielectric, thermal, and chemical properties for transformer service.

A regulating transformer injecting variable voltage in series with a transmission line for precise voltage and power flow control.

An inductive device in power systems to limit current, absorb reactive power, or filter harmonics.

A transformer designed to supply rectifier/inverter loads with enhanced harmonic and DC magnetization handling.

The maximum continuous power output a transformer can deliver at specified conditions without exceeding temperature limits.

A compact factory-assembled HV switchgear set for ring-type or radial distribution networks.

A specialized transformer for railway electrification converting supply voltage for traction motors.

Online diagnostic systems providing real-time transformer condition data including DGA, temperature, and partial discharge via SCADA.

Protective relay schemes detecting transformer internal and external faults, initiating circuit breaker tripping to isolate faults.

Transformers increasing (step-up) or decreasing (step-down) voltage levels based on the turns ratio.

Transformer impedance measured with one winding short-circuited, determining fault current and regulation.

A facility housing transformers, switchgear, and protection for voltage transformation and power routing.

A transformer winding with shielding to reduce surge voltage stress and improve impulse distribution.

A transformer optimized for solar PV plants handling inverter harmonics and variable loading.

Equipment for switching, controlling, and protecting electrical circuits including breakers and relays.

Grain-oriented electrical steel with aligned crystal structure minimizing core losses in transformer magnetic cores.

A static device transferring energy between circuits through electromagnetic induction, changing voltage and current levels.

A device adjusting transformer turns ratio by connecting to different tap points on a winding.

The temperature increase of transformer components above ambient at rated load, a key design parameter.

A transformer for three-phase power systems with three winding sets on a common core.

The ratio of primary to secondary winding turns directly determining voltage transformation ratio.

The sealed steel enclosure containing the transformer core-coil assembly and insulating oil, providing mechanical protection and structural support.

Voltage levels above 800 kV AC or +/-800 kV DC for bulk power transmission over very long distances.

Unequal three-phase loads causing unequal currents, neutral current, and zero-sequence effects.

A tap changer beneath transformer bushings allowing adjustment without entering the oil tank.

The change in secondary voltage from no-load to full-load as a percentage, indicating voltage stability.

Standardized designation of transformer winding connections and phase displacement between HV and LV.

A transformer with continuously adjustable output voltage for testing and voltage control.

The complete system of winding configuration codes for three-phase transformer system integration.

Coils of insulated conductors in a transformer carrying current and linking magnetic flux for energy transfer.

The DC resistance of transformer windings, measured for loss calculation and connection quality verification.

The total real power loss in a transformer in watts, comprising no-load and load loss components.

A three-phase connection with one star and one delta winding providing phase shift and harmonic isolation.

A transformer for wind energy applications including collector system and GSU transformers.

The ratio of reactance to resistance in a transformer determining fault current decay and DC offset characteristics.

Voltage levels 245-800 kV for bulk power transmission over long distances.

A winding configuration with star HV and delta LV, the most common arrangement for power transformers.

A vector group with both windings in star with in-phase displacement, used for small distribution transformers.

Current components equal in all three phases flowing through neutral/ground during unbalanced or fault conditions.

A special transformer with interconnected windings creating a neutral for grounding in three-phase systems.

Total opposition to AC current combining resistance and reactance as Z = sqrt(R^2 + X^2).